- 14 bit arbitrary waveform generator
- 2 synchronous channels with seperate D/A
- Maximum output rate 20 MS/s on 2 channels
- Output up to ±3 V in 50 Ohm
- Amplifier module with ±10 V output level as an option
- Programmable Offset and Amplitude
- Up to 64 MSample memory
- Continuous FIFO mode
- 32 Bit PXI / CompactPCI 3U interface
- Compatible with 3,3V and 5V PCI I/O-Voltage
- Software SPEasyGenerator included
MX.60xx FamilyThe MX.60xx series offers 4 different versions of arbitrary waveform generators for the CompactPCI bus. With these boards it is possible to generate free definable waveforms on several channels synchronously. There are one or two channels on one board with a maximum sampling rate of 125 MS/s. The internal standard Sync-bus allows the setup of synchronous multi channel systems with higher channel numbers. It is also possible to combine the arbitrary waveform generator with other boards of the MX product family like analogue or digital acquisition boards. With the up to 64 MSample large on-board memory long waveform could be generated even with high sampling rates. The memory could be used also as a FIFO buffer to make continuous data transfer from PC memory or hard disk. Model | 1 channel | 2 channels | | 20 MS/s | 20 MS/s | | 60 MS/s | 60 MS/s | | 125 MS/s | | | 125 MS/s | 60 MS/s |
Block diagram
Memory | FIFO Mode: continous data transfer up to 100 MB/s [ more...] |
| Singleshot Output: The programmed memory is generated one time |
| Continous Output: After trigger event the programmed memory is generated continuously in a loop |
| Standard memory 8 MSamples |
| Option memory upgrade to 16 MS, 32 MS or 64 MS on-board memory |
Trigger | External Trigger: Input or output of external TTL signal [ more...] |
| Option Multiple Replay: Output of several segments with short dead-time [ more...] |
| Option Gated Replay: Replay controlled by gate signal [ more...] |
Clock | External Clock: Input or output of sampling clock [ more...] |
| Reference Clock: Used to generate sampling clock [ more...] |
Extras | Bank Switching: Output of two signals controlled by bank signals [ mehr...] |
| ±10 V Amplifier: Extra board with ±10 V output levels and 1, 2 or 4 channels [ more...] |
PXI BusThe PXI bus extension offers a lot of pre-defined lines on the backplane for clock and trigger synchronisation between different boards.
The Spectrum card supports these PXI features: | 10 MHz Reference Clock: Could be used as base for samplerate generation |
| Star Trigger: supported as trigger source for the board |
| Trigger Bus: Direct card synchronisation with the integrated trigger bus |
Software Support | Standard drivers for Windows and Linux as well as examples for C/C++, Delphi and Basic are included in the delivery [ more...] |
| SBench 5: Comfortable measurement software for windows [ more...] |
| Option LabVIEW drivers: Libraries and examples for LabVIEW[ more...] |
| Option DASYLab driver: Direct access to cards with DASYLab [ more...] |
| Option MATLAB driver: Universal driver for all cards [ more...] |
| Option VEE driver: Libraries and examples for Agilent VEE [ more...] |
| Standard drivers for Windows and Linux as well as examples for C/C++, Delphi and Basic are included in the delivery [ more...] |
| Firmware update in the Spectrum Control Center[ more...] |
| SBench 5: Comfortable measurement software for windows [ more...] |
| Option LabVIEW drivers: Libraries and examples for LabVIEW[ more...] |
| Option DASYLab driver: Direct access to cards with DASYLab [ more...] |
| Option MATLAB driver: Universal driver for all cards [ more...] |
| Option VEE driver: Libraries and examples for Agilent VEE [ more...] |
DownloadsApplication Notes
|
